Rubber Belt Tumble Type Shot Blaster Machine for Die Casting Parts
Rubber Belt Tumble Type Shot Blaster Machine Description
Rubber tracked type shot blasting machine is a small shot blasting
cleaning equipment, mainly by the room the shotblast cleaning, shot
blasting machine assembly, hoisting machine, separator, shot
blasting machine electrical system and other accessories.
It is suitable for small and medium sized castings, forgings,
stampings, the gear, spring and other parts of deoxidization, rust
removal, remove scale and surface strengthening, are especially
suitable for the cleaning of parts and reinforcement.
Rubber Belt Tumble Type Shot Blaster Machine
|Items||The main parts|
|Blasting Chamber||Chamber cover, liners, end plate, manual door, etc|
|Blasting Wheel||Blasting Wheel, Motor, Pulley, Triangle Belt, Base Plate, Etc|
|Elevator System||Cover, Elevator Belt Assembly, Pulley, Drive, Tight Device, Etc|
|Separator System||Separator, Shot Bucket, Etc|
|Screw conveyor||Screw shaft, blades, bearing base, etc|
|Tumbling System||Rubber belt, drive shaft and driven shaft, tight shaft, drive
|Pneumatic System For Shot||Shot gate, cylinder, shot- slip pipe, air processor, etc|
|Electronic Control System||Control cabinet (conventional electronic control), the second line,
|Dust Collector System|
Bag type dust collector , sedimentation tank, piping, blower, etc
Rubber Belt Tumble Type Shot Blaster Machine Advantage
1. Compact design, simple operating principle
2. Forced but gentle turning and tumbling of the parts for
all-round shot impingement
3. Targeted high performance shot blasting for specific
4. Continuous and thorough shot removal
Rubber Belt Tumble Type Shot Blaster Machine Operation
1. Add the shots and load in the workpieces, then close the door.
2. Start the fan of the dust collector.
3. Start elevator, blasting wheel and shot supply valve in turn.
4. After finishing cleaning process, stop shot supply valve,
blasting wheel elevator and dust collector fan in turn.
5. After the machine stop completely, open the workpiece feeding
door, unload the workpieces.
6. Emergency stop switch is for emergency situation. The whole
machine will stop immediately after pressing the button.
7. Dust collector should be stop timely after finish all the duty.
Range of Application
1. Ferrous and non-ferrous castings
2. Heat treated forgings
3. Small Automotive parts
4. Die castings and much more
5. Lower value parts where part on part impingement is not an issue
6. When production requires dictate batch processing
7. Small to medium size castings, fabrications and heat-treated
8. Sand removal or part cleaning
Optimised shot blast effect
During shot blasting, the workpieces, regardless of size and shape,
are evenly and continuously tumbled. This is necessary for the
effective and uniform treatment of all surfaces.
During tumbling, the workpieces continually undergo shot removal,
enabling workpiece interiors and cavities to be perfectly cleaned.
For the complete removal of all shot, the final tumbling time that
follows the shot blast sequence can be regulated to suit the type
of workpieces being blast cleaned. The tightly sealed, leak-proof
blast chamber minimises shot consumption.
1. All the machine operator must be to this specification and its
principle of work performance and operation method, lubrication,
etc have a comprehensive understanding, in order to operate;
2. Will the projectile (200 kg) in succession to join chamber body,
and then into the workpiece, closed loading door, ready to drive;
3. Start the filter fan;
4. Start button: in order for pill gate hoist, shot blasting
machine, and began to clean up. Cleaned up after the button closure
in turn: used for pill gate, shot blasting machine, elevator, dust
collector fan, restart vibrating motor ash removal, to a certain
time after the shaking stopped;
5. After shot blasting machine stop completely, open the door of
feeding, will the tooling and artifacts.
6. In case of an emergency, can according to the urgent stop
button, the machine immediately stop all work;
7. All the work has been completed, should be timely close the
8. Everyday after work, all the machine should be clean again;
9. Frequently examine the guard in the clean room and shot blasting
machine, round pill and orientation in the set of wear parts wear,
wear serious, should be replaced immediately;
10. Lubricated periodically according to the rules, and regularly
check whether the machine regulated flexibly.
11. Check the transmission parts regularly, cleaning parts, replace
1. Reply your inquiry in 24 working hours.
2. Experienced staffs answer all your questions in fluent English.
3. Customized design is available. UEM&UBM are welcomed.
4. Exclusive and unique solution can be provided to our customer by
our well-trained and professional engineers and staff.
5. Special discount and protection of sales are provided to our
6. Professional factory : We are manufacturer, specializing in
producing all kinds of machinery for more than 20 years,
competitive with good quantity.
7. Sample: We can send out sample for test in one week if the order
quantity is big enough. But the shipment charges is usually paid by
your side, the charges will be rebounded when we have formal order.
8. As an honest seller, we always use superior raw material,
advanced machines, skilled technicians to ensure our products to be
finished in high quality and stable feature. Welcome to contact us
or visit our company.
If you are interested in our machine,please kindly inform us the
1. The name of your workpiece?( such as: iron casting parts,
Aluminium auto parts etc.)
2. The purpose of the blasting?(rust removal or others?)
3. The size range of the workpiece?( max size and min size)
4. The weight of the workpiece? (max weight and min.weight)
5. The cleaning capacity per day/month?
6. Any other technical requirement?
Pictures for Reference